Showing posts with label NY. Show all posts
Showing posts with label NY. Show all posts

Understanding Load Cell Overload

Load Cell Overload

When you're talking about load cells in process weighing, what does safe and ultimate overload mean, and how strong are load cells?


The ultimate strength relates to the function as a load cell and not the mechanical strength. The mechanical strength of the load cell is even higher. 


For a load cell, there is generally three capacity limits:  


The nominal capacity of one 100%: Let's say we have a 100-pound load cell. This is the limit or capacity of the load cell. Note the load cell should not be subjected to higher forces under regular use. If the application needs to measure higher loads, then a larger load cell should be used.


The safe load usually is 200 percent of the rated capacity: Let's say with the 100-pound load cell this would be 200 pounds. If the load cell is occasionally subjected to more than 100 percent but less than 200 percent, nothing happens to it, and it will work. If repeatedly subjected to more than 100%, the load cell can be damaged due to fatigue.


The ultimate load is usually 300 percent of rated capacity or 300 pounds for a 100-pound load cell. If the load cell is occasionally subjected to a load greater than 200 percent but less than 300 percent, the load cell will be subjected to a zero shift. However, in most cases, the load cell can be recalibrated and repaired. If subjected to more than 300 percent, the bonding of the strain gauges will most likely be damaged beyond repair. The function of the load cell is damaged, and it should be scrapped. 


As a reminder, this refers to the function as a load cell and not the mechanical part. The mechanical strength of a load cell varies but is often in the range of 400 to 1 000 percent. It should also be noted that there's a fatigue limit for a load cell that generally is 133 of capacity. 



The Dynisco LMI5500 Series Melt Flow Indexer

Dynisco LMI5500

Of all the tests used by the plastics industry, melt flow rate testing (or melt flow index) is the most widely used. It is traditionally associated with testing polyethylene materials to determine the lot-to-lot consistency of resin lots or batches for quality control purposes. It is, however, also used for other purposes such as testing new materials, determination of material stability versus residence time within plastics processing equipment, or the assessment of regrind content within materials or moldings. It is generally a low shear rate test; however, larger weights can increase the shear rate.

A flow rate test measures a polymer’s mass flow rate (grams extruded in 10 minutes) using an orifice under specified conditions of temperature and load. Machines that determine flow rate are generally called Melt Indexers or Extrusion Plastometers. Test methods by ISO, DIN, ASTM, and others specify heat chamber and piston tip diameter such that the shear stress on the polymer is the same in all machines for a given load. In addition, material specification guidelines (by ISO, DIN, ASTM, GM, etc.) may exist, providing further constraints on how a particular material processes.

Specifically designed for the thermoplastics resin industry, the Dynisco LMI5500 Series Melt Flow Indexer has an array of features and benefits that range from ground-breaking accuracy to a unified software platform between all laboratory and online production equipment.

(508) 351-6200

The Micro-Measurments Model 700B Next Generation Welder

Micro-Measurments Model 700B

The Micro-Measurements Model 700B Welder is the next generation of the Model 700 Welder, which has been used for decades to install tens of thousands of strain gages worldwide. This experience and customer input and support provide more capability and flexibility while remaining in a smaller, more portable package. 

This new welder combines a high-speed spot welding rate with the enhanced safety and portability features that you have come to expect from Micro-Measurements. It is designed for spot welding the Micro-Measurements line of CEA, LWK, LEA, LZN, and LZE weldable strain gages. In all types of adverse field conditions, the 7rugged 00B performs efficiently and dependably.

The 700B's use of commercially available Lithium-ion batteries, which are easily replaced in the field and can handle 1500 welds (@30 joules) on a single charge, is a significant improvement (equivalent to welding around 30 linear weldable gage). The lightweight unit weighs approximately 8.3 lb. (3.77 kg) and is ideal for field use, overcoming the main limitations of other portable spot welders on the market. The unit also welds small thermocouples and light-gauge metal  

The Model 700B enhances Micro-Measurements' broad portfolio of weldable gages suitable for all types of applications and environments. Encapsulated, sealed, and high-temperature versions of Micro-Measurements' CEA, LWK, LEA, LZN, and LZE product families are included. Weldable sensors can be easily installed in field applications under a wide range of weather conditions because they are spot-welded rather than adhesively bonded." 

The Model 700B's welding energy can be easily adjusted by the user from 10 to 60 Joules, with a weld rate of up to 60 welds per minute, making it one of the fastest tools of its kind. The 700B is simple to clip onto a harness or carry around remote job sites, whether working suspended under a structure or in a manufacturing plant. It is particularly well-suited for working from rope access, aerial lifts, or in a laboratory setting. ​

For more information in New England, contact AP Corp. Call (508) 351-6200 or visit https://a-pcorp.com.

The Druck DPI705E Series Handheld Pressure Indicators


The Druck DPI 705E Series of handheld pressure and optional temperature indicators combine tough and rugged design with accurate and reliable measurements.

Compact and robust, the DPI 705E Series is designed for single handed operation and provides many essential features required for routine maintenance and system troubleshooting.

DPI705E Series Handheld Pressure Indicator Features

  • 48 pressure ranges from ±25 mbar to 1,400 bar (±1.69 psi to 20,000 psi / 2.5 KPa to 140 MPa)
  • Total 1 year uncertainty down to 0.05% full scale (FS) over temperature range of -10°C to +50°C
  • Integral calibration record with calibration due count-down display
  • Rugged, handheld design with backlit high-contrast display
  • Leak test, tare, maximum/minimum and filter
  • Hazardous Area (Intrinsically safe) version available
  • Optional remote plug and play pressure and Resistance Temperature Detector (RTD) sensors
  • Optional pneumatic and hydraulic hand pumps

For more information in New England, contact AP Corp. Call (508) 351-6200 or visit https://a-pcorp.com.

In-Line Color Measurement in the Molten Polymer

In-Line Color Measurement in the Molten Polymer

Color measurement is a widely used technology for ensuring the quality of color values during the manufacturing process. Typically, these measurements happen offline. The time it takes between sampling and receiving results from the laboratory can be lengthy. A significant disadvantage is that only one measurement occurs during this period, and the color quality during, before, and after the sampling point is unknown. A complete analysis is possible because inline color measurements are performed directly in the melt, but when color variations occur, immediate intervention is possible.

Inline color measurement will provide product-quality indicators for immediate and automatic adjustment of process parameters. The outcome is to maintain the highest possible product quality without waiting for sample analysis from the plant's laboratory.

Equitech International Corp. has been in business since 1995, supplying fiber-optic spectroscopic instruments for process analysis to pharmaceutical, chemical, and food manufacturers. In 2005 they entered the plastics market and began extending their technology into inline color monitoring and real-time closed-loop process control. They published a helpful Technical Paper titled In-Line Color Measurement in the Molten Polymer. You can download that paper here.

Dynisco Polyclean Fluidized Baths

Dynisco Polyclean Fluidized Baths

Cost-Effective, Fast, and Safe Way to Clean Various Plastic Processing Components

The Dynisco PolyClean Fluidized Temperature Baths come in three models and offer a cost-effective, fast, and safe way to clean various plastic processing components. PolyClean Fluidized Temperature Baths are applied in any polymer manufacturing or laboratory facility that needs minimal operator interaction and a low risk of harm to essential design requirements of a part during the cleaning process. 

The PolyClean 6L Fluidized Temperature Bath is ideal for cleaning small tooling from laboratory extruders or injection molding machines. 

The PolyClean 12L cleans extrusion tooling and other forms of hardware, forms parts, calibrates and tests various sensors and systems, heat treats metals and heats reactors, coils, flasks, and containers. 

The  26L PolyClean has similar functions and benefits to the PolyClean 12L, but its 26" deep basket allows it to clean larger components than the PolyClean 12L

For more information in New England and Upstate New York, contact AP Corp by calling (508) 351-6200 or visiting https://a-pcorp.com.

AP Corp. Selected Druck New England Representative

AP Corp. is ow The Druck New England Representative

AP Corp. is delighted to announce that they are now the New England Sales and  Engineering Representative for Druck piezo-resistive pressure sensors and test/calibration instruments.

Druck, a Baker Hughes business, manufactures the high-reliability piezo-resistive pressure sensors and test and calibration instruments known for performing in the most challenging environments. Their products provide customers with the highest performance, stability, quality, accuracy, and quickest response in any environment.

Druck's product line includes pressure sensors,  OEM custom sensors, PACE Pressure Controllers, handheld process calibrators, pressure indicators, test tool instrumentation, and  4Sight2 Calibration Management Software.

The addition of Druck extends AP's offering of high quality, best-in-class, engineered sensor solutions. AP Corp's application expertise and long-standing customer relationships in New England are vital to providing Druck with accelerated sales growth in this territory.

For more information, contact:

AP Corp.
One Tara Boulevard
Suite 200
Nashua, NH 03062
www.a-pcorp.com
508-351-6200 (office)

Process Weighing, Web Tension, and Force Control Systems Applications in Pulp and Paper Production

BLH AP Corp

BLH Nobel is a leading supplier of specialized pulp and paper measuring devices. Over the years, they've built a strong understanding of pulp and paper manufacturers' process problems. Be assured that BLH Nobel has the best solutions to maximize productivity and performance.

DOWNLOAD THE BLH PULP & PAPER APPLICATIONS GUIDE HERE

Pulp and Paper Applications

  • State-of-the-Art Instrument for Weighing and Force Measurement
  • Web Tension Measurement Unit
  • Dynamic Resultant Force Measurement
  • Refiners Position and Pressure Control
  • Paper Rolls, Pulpers and Coating Kitchen

Micro-Measurements Strain Gage Instrumentation Catalog

Strain Gage Instrumentation

Explore Micro-Measurements complete catalog of data acquisition instruments.

Micro-Measurements offers a comprehensive range of specialty instruments for data acquisition. With Micro-Measurements instruments, you can capture fully corrected, accurate engineering-unit data with minimal effort. Their special-purpose equipment, backed by highly skilled engineers' expertise and knowledge, complements strain gage installation integrity and instrument calibration.

DOWNLOAD THE CATALOG HERE

Product Range:

  • High-speed data loggers
  • Single-channel devices
  • Portable indicators
  • Multi-channel data acquisitions systems
  • High-bandwidth signal conditioners
  • Signal conditioning amplifiers
  • Embedded analog-to-digital convertors
  • Inputs for other commonly used sensors, including load cells, displacement transducers, thermocouples, and accelerometers. 
For more information about Micro-Measurements in New England and Upstate NY, contact AP Corp. Call them at (508) 351-6200 or visit their website at https://a-pcorp.com.

The QSO® Quick Shut-off Valve from Glycon Corporation

A better quick shut-off non-return valve for the Plastics Industry.

QSO Valve by Glycon
Injection molding applications require two important criteria from a non-return valve:

  1. Rapid material shut off for part weight consistency
  2. A smooth, high-flow profile to prevent material degradation. 

The Glycon QSO® valve is the only valve that provides you both. The result is higher quality parts, fewer rejects, improved yield, and a better return on every pound of material you run.

Compared to traditional ball and ring check valves, only the QSO® Quick Shut-off Valve delivers both high flow and raid shut-off. Plastics molders prefer the QSO® because:

  • The QSO® ends short shots!
  • The QSO® reduces scrap rates
  • The QSO® optimize part weight consistency
  • The QSO® prevents material degradation
  • The QSO®is perfect for filled materials
  • The QSO® eliminates need for decompression or “suck back”
  • The QSO® maintains smooth material flow path
  • The QSO®is designed for long lasting and durable
QSO Valve by Glycon


Web Tension Control in Paper Production

BLH Nobel web tension systems comprise off-the-shelf standard modules and electronics, as well as customized systems. BLH Nobel designs force measurement modules according to the customers’ mechanical requirements and forces, ranging in size from just a few Newtons to mega-Newtons. The combination of digital signal amplifiers and stable force transducers means that BLH Nobel systems can handle anything from applications with a low tare and large forces, to those with a large tare and small forces.

For more information about BLH Nobel products in New England, contact AP Corp. Call them at (508) 351-6200 or visit their website at https://a-pcorp.com.

EASYHEAT Induction Heaters from Ambrell Corporation

Easyheat Induction Heaters
EASYHEAT advanced induction heating systems by Ambrell Corporation provide a flameless, non-contact, reliable, compact solution for heating your parts with a quick, clean source of heat. Available in models from 500 Watt to 10 kW, all are ideal for repeatable, energy-focused heating of your parts.

Flameless, non-contact induction heating minimizes energy waste by focusing energy only on the part and zone to be heated. Select and monitor power levels from the front panel LCD and sealed touch pad. Remote power control is available for employing contact inputs, analog inputs or optional serial data port. Easily control the length of the heating cycle with a built-in programmable digital timer.

Download the Ambrell EASYHEAT® 500 Watt to 10 kW Induction Heater Catalog here.

For more information about Ambrell products in New England, contact AP Corp. Call them at 508-351-6200 or visit their website at https://a-pcorp.com.

New Bench Top Series of Shaker Systems from Sentek Dynamics

Bench Top Series of Shaker Systems

The BT Series shakers from Sentek Dynamics are designed for demanding vibration test applications. Typical applications included structural analysis, calibration and testing of smaller assemblies. The BT-100 through BT-400 shakers utilize light weight rare earth magnets in lieu of traditional Alnico magnets. The use of these magnets decreases the total shaker mass to a third of similar size system, making these shakers easy to handle and portable. 

The systems range in size from 100 N (70 lbf) to 1000 N (224 lbf). Systems 400 N (99 lbf) and smaller are permanent magnet shakers and use lightweight rare earth magnets, making these systems easy to handle and portable. There are three versions of the BT Series of shakers: the BT, BT-M and BT-MTH.  

The BT Series is recommended for vibration testing of small assemblies and components. These shakers have armature diameters from 60 mm (2.36 in.) to 120 mm (4.72 in.). The BT-1000 is equipped as standard with Automatic Armature Centering (AAC) and Air-Isolation Feet (AIF).  

The BT-M and BT-MTH Series are our modal shakers lines. BT-M will use standard stingers while the BT-MTH is our through-hole version. On the 100 N and 200 N system the BT-MTH offers over double the displacement. The BT-MTH Series allow you to use piano-wire stingers. The BT-1000-M is ideal for the structural and modal analysis of high-mass structures. The addition of ZPR (electronic zero-point regulation and adjustable suspension stiffness) allows the user to pre-load the structure prior to applying a dynamic load.

The new Sentek Dynamics Bench Top and modal exciters are based upon years of practical experience. These systems all exhibit a high lateral stiffness and high force-to-weight ratio. They are specifically designed to help ensure the best possible performance with minimum setup time. 

Contact AP Corp. regarding any Sentek Dynamics product in New England and Upstate New York. Call us at (508) 351-6200 or visit our website at https://a-pcorp.com.

About Induction Heating

What is induction heating?

About Induction HeatingInduction heating is a fast, efficient, precise, repeatable, non-contact method for heating metals or other electrically-conductive materials . An induction heating system includes an induction power supply which converts line power to an alternating current, delivers it to a workhead and work coil creating an electromagnetic field within the coil. The work piece is placed in the coil where this field induces a current in the work piece, which generates heat in the work piece. The coil, which is water-cooled and cool to the touch, is placed around or adjacent to the work piece. It does not touch the work piece, and the heat is only generated by the induced current flowing in the work piece.

Induction heating is used in processes where temperatures are as low as 100 oC (212 °F) and as high as 3000 °C (5432 °F). It can be used in brief heating processes that are on for less than half a second and in heating processes that are on for months.

Induction heating is used in domestic and commercial cooking, and in many applications such as melting, heat treating, preheating for welding, brazing, soldering, curing, sealing, shrink fitting in industry, and in research and development.

Learn more about induction heating by downloading the "About Induction Heating Solutions" technical note courtesy of Ambrell Induction Heating Systems.


AP Corp.
(508) 351-6200

In-Line Turbidity and Haze Measurement

Equitech's Retro-Reflection Probe
Photo 1: Equitech's Retro-Reflection Probe
Monitoring turbidity and haze of liquids and sheet is an indicator for product quality. Examples include: polymer extrusion, resins and chemical production. Real-time adjustments of the process parameters are therefore possible through immediate "off-specification" detection.

INTRODUCTION 

Turbidity and haze measurement is a well-accepted technology to check the consistency some production processes. Usually these measurements are performed ‘off-line’.  
The delay between sampling and obtaining the results from the laboratory can be time consuming. A significant disadvantage is that only a single measurement is generated in this time period and the concentration during, before and after the sampling point is unknown.  

With the inline turbidity and haze measurements taking place directly in the process, not only is complete documentation possible, but when variations occur, immediate intervention can take place.

INNOVATION 

The Equispec™ In-line Color Spectrophotometer (ICS) is a high performance instrument designed for use in an industrial pro-cess. Its excellent sensitivity and flexibility make it useful for process applications. The ICS and process probes are designed to be used in high-temperature, high-pressure and corrosive environments. It can be used to analyze  liquids and solids. 

The analyzer supports one or two probes with dedicated lamp compensation channels [all fiber-optic double-beam design]. 

EquiColor Software
Photo 3: Trend charts of EquiColor Software
TURBIDITY AND HAZE MEASUREMENT 

Equitech’s fiber-optic probes allow for easy access into the process. Equitech offers probes for both turbidity and haze measurements.  This includes insertion/immersion probes (see Photo 1). 

The spectrophotometer is integrated in a NEMA4 box with an industrial computer and touch-screen (see photo 4). The appropriate spectral range is 380-780 nm (resolution 1 nm). The NEMA4 box is made from stainless steel. It is designed and equipped specifically for use in the production environment where the ambient conditions can be dusty, vary in temperature, subject to vibration etc. The box also contains a thermoelectric cooling and heating device to eliminate the influences from ambient temperature by keeping the temperature inside the box at a constant level. 

Turbidity and haze
Photo 2: ICS stainless steel NEMA4 box with touch-screen
INSTALLED APPLICATIONS INCLUDE 

Resin Production, Sheet Production,  Filter Breakthrough, Surfactants 

Turbidity and haze are calculated from the spectral curve,  and displayed as trend charts by the EquiColor™ software (see photo 3). 

For more information, contact AP Corp. Call them at (508) 351-6200 or visit https://a-pcorp.com.

Plastics Industry Feed Screw Classification White Paper

The feed screw is used in plastics extrusion to force melting plastic resin through a die into a mold to form a desired shape. As screw designs have evolved through the years, there are several generic categories.

Glycon Corporation, the industry leader manufacturer of high performance and innovative feed screws, has put together this white paper describing the classifications of feed screws used in the plastics industry.








AP Corp.
https://a-pcorp.com
(508) 351-6200

The Badger Meter Cox EC80 Flow Processor

Cox EC80 Flow ProcessorThe Cox EC80 Flow Processor is a programmable electronic processor, providing total compensation to enhance flow meter accuracy, while extending the linear flow range. Packaging is provided for remote, direct or embedded mounting to support most installation or application requirements.

The compact design includes both single and dual frequency inputs from 4 or 10 ohm pickups, as well an RTD input and an additional analog input for other temperature inputs. The EC80 processor tracks all variables to compensate for viscous and inertial effects, using proven Strouhal-Roshko algorithms. Enhanced DSP technology allows for exceptional signal characterization using a 32-bit floating point processor at 150 MHz, capable of producing a 100 microsecond speed of response.

Cox EC80 Flow Processor Applications

  • Precision monitoring
  • Engine test cells and test stands
  • On-board automotive and aerospace testing
  • Control loops
  • Custom OEM flight and commercial applications

Cox EC80 Flow Processor Industries

  • Aviation & Aerospace
  • Petrochemical, Refining & Chemical Metering
  • Process or Industrial
  • Test Equipment & Services



For more information, contact AP Corp. Call them at 508-351-6200 or visit their web site at https://a-pcorp.com.

Bonding Strain Gages? 5 Steps to Getting Surface Prep Right!


When bonding Micro-Measurements Advanced Sensors Technology strain gage sensors (CEA, C4A, C5K)  you want to ensure an excellent bond. The key element in bonding strain gages is surface preparation.

The video above demonstrates specific procedures and techniques with proven advantages. By precisely following these carefully developed instructions (along with the requisite procedures for gage and adhesive handling), the result will be strong and stable bonds. This video presents a procedure that is simple to learn, easy to perform, and reproducible. Keep in mind, it is very important to pay attention to detail and follow the instructions precisely. The importance of surface preparation for strain gage bonding cannot be understated.

1) Degreasing

Rigorously  degrease the gaging area with a good solvent, such as CSM Degreaser or GC-6 Isopropyl Alcohol. Be aware though that some materials (e.g., titanium and many plastics) react with strong solvents. Make sure your solvents do not contain any contaminants

2) Abrading

Preliminary dry abrading with 220 or 320-grit silicon-carbide paper is generally required if there is any surface scale or oxide. Final abrading is done by using 320-grit silicon-carbide paper on surfaces thoroughly wetted with M-Prep Conditioner A; this is followed by wiping dry with a gauze sponge. Repeat this wet abrading process with 400-grit silicon-carbide paper, then dry by slowly wiping through with a gauze sponge.  Finish with 320 grit on most steels and 400 grit on aluminum alloys.

3) Burnishing of Layout Lines

Using a 4H pencil (on aluminum) or a ballpoint pen (on steel), burnish (do not scribe) whatever alignment marks are needed on the specimen.


4) Conditioning

Repeatedly apply M-Prep Conditioner A and scrub with cotton-tipped applicators until a clean tip is no longer discolored. Remove all residue and Conditioner by again slowly wiping through with a gauze sponge. Never allow any solution to dry on the surface because this invariably leaves a contaminating film and reduces chances of a good bond.

5) Neutralizing

Now apply a liberal amount of M-Prep Neutralizer 5A and scrub with a cotton-tipped applicator. With a single, slow wiping motion of a gauze sponge starting within the clean area and wiping outward in one direction.  Repeat the wiping step with a clean gauze pad, again, start in the clean area, wipe though the gage location moving outward in a single stroke to fully dry this surface. Do not wipe back and forth because this may allow contaminants to be redeposited.

For proper outcomes, the procedures and techniques presented here should be used with qualified installation accessory products from Micro-Measurements, namely:
  • CSM Degreaser or GC-6 Isopropyl Alcohol
  • Silicon Carbide Paper
  • M-Prep Conditioner A
  • M-Prep Neutralizer 5A
  • GSP-1 Gauze Sponges
  • CSP-1 Cotton Applicators
  • PCT Gage Installation Tape
For more infomration, contact AP Corp. Call them at 508-351-6200 or visit their web site at https://a-pcorp.com.

New Product Alert: A Noise Monitoring Station with Built-in Noise Directivity Detection


The SV 200A is a Class 1 sound level meter integrated with a wireless communication via 3G, LAN, Wireless LAN and Bluetooth®. The list of add-ons also includes a built-in electrostatic actuator, GPS module and e-compass. The waterproof power supply is also provided.

The SVANTEK SV 200A is the top-of-the range noise monitoring station with built-in microphones for noise directivity detection. This innovative, new product enables the identification of dominant noise sources providing information about their location both vertically and horizontally. In practice, measuring directionality gives the opportunity to indicate the dominant source of noise in the measurement area or exclude unwanted events.

Four additional microphones located on the sides of the housing use the sound intensity technique to recognize both the vertical and the horizontal direction of a dominant noise source. Leq distribution in angle sectors is saved as time-history and can be used to filter and report data.

The SVANTEK SV 200A can perform a 1/1 and 1/3 octave frequency analysis in real-time and store it as time-history data. It can also record the audio signal for the recognition of noise sources and recalculation of the data.

The advanced alarm function can send email and SMS notifications caused by threshold levels and time events. Status alarms of the SVANTEK SV 200A are also available.

The 3G modem, Wi-Fi and LAN features provide fast Internet transfer to PC with standard internet connectivity. SvanNET enables Internet plug & play and easy management of measurement projects. Irrespective of the type of a public or private sim card, SvanNET will make a connection to allow full access to your data via Web browser. The Bluetooth ® and Wireless LAN features provide a point of access for easy SvanNET application configuration.


For more information on SVANTEK products in New England and New York, contact AP Corp. Call (508) 351-6200 of visit https://a-pcorp.com.

Occupational Health & Environmental Sound and Vibration Meter: The SVAN 977A


The SVAN 977A is a class-one sound and vibration level meter that offers unprecedented state-of-the-art technology designed for general acoustic, occupational health,  and building acoustic measurements of  vibration and environmental noise. The instrument comes equipped as standard with the SV7052E polarized half inch microphone, the SV12 microphone preamplifier, and the SA22 foam windscreen, as well as a large 16 gigabyte internal memory which can be easily upgraded by a micro SD card. The meter comes equipped with a standard quarter inch photographic thread. On the bottom panel you can locate the usb serial and I/O sockets. There is also a micro SD card slot under the bottom cover and spaces for the four double a batteries. The SVAN 977A is equipped with a super contrast led color display. The instrument's user interface makes both configuration and measurement easier than ever before. The user can easily operate the instrument by selecting the appropriate position from the selected menu lists.

The instrument has 2 general modes of operation: Configuration mode; and measurement performance and results preview mode. The SVAN 977A can be used in the meter mode to perform the real-time 11 octave or 1/3 octave analysis including calculations of statistical levels, and can also perform FFT analysis.  For building acoustic applications SVAN 977A offers reverberation time measurements RT60 and building acoustics assistant application for smartphones.

With a special microphone the meter provides measurement range of the ultrasounds up to 40 kilohertz. Measurement results can be viewed indifferent view modes, the set of which you can change and activate depending on the selected measurement function. If you disconnect the microphone preamplifier, you can use the instrument to take vibration measurements simply by connecting a cable and a vibration sensor.  SVAN 977A can be easily installed into the SM277 case and used as an outdoor monitoring station thanks to a dedicated modem station which enables connection to the SVAN NET, an advanced server solution supporting remote connection giving users full access to the measurement data via web browser or dedicated application.

For more information, contact AP Corp. by visiting https://a-pcorp.com or by calling (508) 351-6200.